Linen Suits - 8 Color [Linen Suit] - $99.99 : Makeyourownjeans.com, Custom Jeans

Product 4/6

Please Choose:

You can select a ready size from the dropdown below OR enter custom measurements options available.
Click her to See our ready size chart.

Jacket Size

All custom measurement trousers leg bottoms are hemmed, Our ready sized trousers are un-hemmed, if you want hemmed legs menition this in the comment box.

Trouser Size

Name of the person for whom these jeans are to be made.

For

Height

Gender

Measure around the lower part of your neck, placing one finger between tape measure and neck

Neck

Measure around the fullest part of the chest (do not puff up chest)

Chest

Place tape where sleeve joins body of coat and measure to length desired. .It is best to measure sleeve length of your existing coat/jacket.

As a reference you can see this chart, click here

Sleeves

Measure from one end of the shoulder to the other across back.

Shoulder-

Measure from the upper end of the shoulder where it joins the neck to the length required.

As a reference you can see this chart, click here

Front Length-

The Weight and Cost increases as the size increases, we charge only for the extra shipping and material accordingly (Please choose the appropriate to avoid delay in your order)

Add'l Information

~Trouser Fit

Measure around the widest part of the Stomach.

~Stomach

Measure and just mention the waist you want, it also depends on how high or low you wear your pants. Make sure the tape is snug, but not pulling tightly, and not too loose.
Measure over trousers or similar clothing.

(Do NOT mention your label size, measure your waist according to the instructions above, readymade pants are always more than their label sizes and vary from brand to brand)

~Waist

Seat is the widest part of the area in the picture next to you. Keep the measuring tape here and the area which gives the maximum measurement is the "SEAT" required..

~Seat

For the Thighs you can give your Body Measurement or Fix Measurements.
Choose your option below and read the respective instructions.
If you select FIX measurements be sure to add the word FIX after the thigh measurement

Determine the widest part of your thigh and measure according to the picture , we will leave our standard loosing, we leave the loosing according to the fit you choose, for example if you choose Baggy we leave much more loosing than say for a Bootcut fit which is supposed to be fitting in the thigh area.

~Thighs

Stand straight and measure around the circumference of the knee joint, we will give the appropriate loosing according to fit.

(If you want us to make the pants with a particular knee measurement just type the word FIX after the knee measurement, eg: 18 FIX (this may be from your favorite pair of Pants), we will manufacture the Knee part of the trouser with this particular measurement.)

~Knee

Measure the length from the waist to the floor or the length you want, you should measure the length while wearing you shoes. Measuring outer length on your existing pants will be better, you should measure it from the top of the waist band to the leg bottom or the length you want.
Please note this is outer length and NOT inseam.

~Length(Outer)

Measure width around cuff as shown.

~Trouser Leg Bottom

Front Rise
Measure from the top of your front waistband to where all the seams meet at the crotch.
Make sure the tape measure is comfortable.
With your hand under your crotch grab the tape measure wear you feel your crotch seams meet.
We can make any rise, so feel free to give measurements of Low rise or Ultra lowrise, high rise or anything in between.

~Front Rise

Back Rise
We can keep the back rise according to our expert's knowledge but if you want a certain back rise measurement you can specify it here.
Same as the front but now in the back. Measure from the top of your waistband at the back straight down to where the seams meet.

We will increase/decrease the back rise incase we feel that it seems a bit incorrect, however if you are very sure of your back rise just mention in the comment box that you want the back rise as specified.

~Back Rise

~Pleats